How Sealing Your Marble Shower?

/in /by

Test to see if your shower needs to be sealed. Unless you have a white marble shower, you should not seal your shower. You should also not seal your shower if there is already an existing seal on it. Test to see if there is sealer by putting a couple of drops of water onto the surface of the shower and allowing the water to dry for ten minutes.


If the area is dark, it means that your marble has absorbed the water and most likely needs to be sealed again. If the sealer has pooled on top of your marble, it means that it’s already sealed. If your shower is already sealed, there’s no reason to do it again, and it can actually be detrimental to your marble.

Dust and clean the inside of your shower with a damp rag. The first step before you seal your shower is to make sure that all the dust and dirt that may be built up is removed before you seal it in. Wipe down your shower with a damp rag and water, then dry it with a clean rag. Make sure that your shower is dry and free of dirt before you start sealing.


Spray down your shower with the sealer and wipe it in. Spray down your shower with the sealer and use a sponge or a rag to wipe the sealer in. Work your way from the top of the shower to the bottom of the shower and try to apply even coats throughout it. Some popular brands of marble sealer include DuPont Stone Sealer and Miracle Sealants.


It’s important that you get a penetrating sealer and not a topical sealer for stone like marble. Allow the sealer to soak for 15 minutes. During this period the sealer will be absorbed by the marble. You should start to see the marble turn a darker color as it absorbs the sealer.

How Removing Deep Stains?

/in /by

Mix 1 part baking soda with three parts water. Combine the baking soda with the water in a small bowl or cup. Continue to mix it together until the baking soda absorbs the water and forms a paste. If your paste is too thick, add more water to it. If the paste is too runny, add more baking soda.


Apply the paste to the stains. Wear gloves and use your hands to smear a good portion of the paste over the stains on your shower. Target any discoloration or built up mildew that you weren’t able to remove from a basic cleaning. Cover the paste with plastic wrap. Tape the ends of the plastic wrap so it stays in place.


Don’t cover all the edges in tape so that the marble can breathe. Let the paste sit on your shower for 24 hours. The paste will dry and absorb the stain under it. When the paste is ready, it should be dry and hard. Remind people in the house that you are doing a deep cleaning and that they won’t be able to use the shower.


Rinse and wipe down the baking soda. Remove the baking soda paste from your shower by rinsing down your shower and wiping the stained areas with a rag. If you notice that the stain is still visible, repeat the steps until it is fully removed. Clean your screen with saliva. Saliva contains enzymes and bacteria that literally consume the dirt on the shower screens.


This is useful if you want to clean a spot where dirt is concentrated. Use a bleach solution to remove any mildew or mold. Mix ⅓ cup (80 ml) of bleach with 1 gallon (3.79 L) of water. Wear gloves and scrub the bathtub and the edges where the caulk used to be with the solution. Make sure that the room is well-ventilated. Use a stiff scrubbing brush to scrub the bathtub with bleach.

How to Clean a Marble Shower?

/in /by

A marble shower is an elegant and chic addition to anyone’s bathroom. Unfortunately, there are also drawbacks with marble, especially when you have to clean it. Marble is a porous rock that tends to absorb chemicals and dyes that are found in traditional cleaners. For this reason, many different things can end up ruining your shower’s sleek finish.


Luckily, if you use the right techniques and limit the chemicals you use when you clean, you can have a shiny marble shower that’s free of stains and dirt. Wipe down your shower after each use. It’s important that you wipe it clean after every use because the chemicals found in your soap may hurt the marble. Use a dry cotton rag or dishcloth to wipe the moisture from the walls and basin of your shower after you use it.


Get your shower walls completely dry. If you just dry your shower walls every day after you use it with a squeegee or a couple of microfiber towels, you will almost completely eliminate the need to have to clean your shower. It’s that leftover water that creates soap scum. If you’re not doing that, you’ll need to clean your shower about once a week to keep mildew and mold away.


Fill a spray bottle with warm water a tbsp (14.7 ml) of mild dish soap. Use regular warm water to fill a spray bottle and add a tbsp (14.7 ml) of non-abrasive, pH-neutral, dish soap into the bottle. Select an undyed dish soap that does not contain any abrasives like sand or stone, and that doesn’t contain any acids like citrus, lemon, or vinegar.

Black Diamond，Simple Green和Zep Marble Cleaner. It will say pH-neutral on the label of your dish soap. Conventional cleaners may contain acids that can damage the surface of your shower. There are specially made marble cleaners that you can purchase at department stores or online. Popular commercial marble sprays include Black Diamond, Simple Green, and Zep Marble Cleaner.

How to Clean a Travertine Shower?

/in /by

Travertine is an attractive type of limestone known for its looks and durability. Naturally, some people choose it as a shower finish. Riddled with small, natural holes, travertine is beautiful, but prone to collecting soap scum. By performing routine cleaning and protecting your travertine, you can keep your shower looking great.

Remove hard water stains with fine steel wool. Be sure to choose 0000-grade steel wool, as it is very fine and shouldn’t scratch the tiles. Lightly buff away hard water stains with the steel wool. Rinse the shower with warm water. Turn the shower on and rinse your newly cleaned travertine tiles with warm water.

If there are any spots you can’t reach with the showerhead, fill your bucket up with clean water and rinse the tiles clean manually. Dry your travertine with a clean towel. Use a towel to wipe down your travertine to remove any traces of stone cleaner. It may be helpful to open a window to dry the area more quickly.

Get your travertine sealed once a year. Sealing your travertine makes the stone more resistant to damage from soap, grit and hard water. Have a stone professional seal your travertine once a year to keep it looking and functioning great.

Allow the sealer to set for 24 hours. Let the sealer fully absorb and dry into your marble before trying to use your shower again. You should seal your marble bathtub once every six months. Let everyone in your house know that using the shower before the sealer dries could damage your marble.

How Protecting Your Travertine?

/in /by

Squeegee and wipe down your travertine after showering. Use a squeegee to remove excess water from the tile after showering. Then, use a towel to wipe your travertine dry to keep soap scum from building up over time. Plus, it’s easier to remove soap residue before it dries.

Pay special attention to pools of water in corners and around edges. If you have a glass shower door, leave it open after showering to allow the water to dry. Establish a regular cleaning routine. Soap scum can cause hard water deposits to accumulate on your travertine. To keep your shower looking its best, clean your travertine shower with non-acidic cleaner a once a week.

If you have a detachable shower head, use it to rinse the tile with warm water after showering to remove soap scum. Creating a calendar reminder can help you remember to incorporate cleaning your shower into your household routine. Clean travertine as soon as something spills.

Whether it’s a colored shower gel or shampoo tinted to enhance hair color, when something spills on your travertine, clean it up right away. Certain bath products contain dyes, which can permanently stain your stone. Inspect grout and tiles for damage.

Bits of grout breaking off can scratch your travertine and trap dirt and grime. Cleaning is a great time to get up close and personal with your tile. Examine your grout and stone for cracks or chips. Be sure to replace chipped or broken tiles and have your grout touched up wherever necessary.

How to Clean an Enamel Bathtub?

/in /by

If you have an enamel bathtub, regular cleaning and maintenance will keep it looking beautiful. Wash your enamel bathtub every week using soapy water and a soft cloth. Remember to dry the tub after every use and fix leaks that could cause staining. To remove stains, avoid abrasive cleansers or tools. Instead, apply cleansing solutions and let them soak on the stain. Wipe and rinse away the solution to reveal your clean enamel tub.

Empty out your shower. Remove all bottles, soap, razors, and accessories from your shower. Wipe down the items to remove any grime that may be transferred back into the shower, especially mildew. Mildew on the bottom of the bottles can immediately rub back onto your freshly clean shower surfaces. If you have any empty or worn-out items, throw them away.

If you have a shower curtain, it’s best to take it down and clean it. Rinse away any loose dirt and debris. A pre-rinse will ensure that you do not accidentally grind dirt or debris into the surface of your tub. It also allows the cleaning product to work directly on the stuck-on grime.

Ventilate the room. Open the bathroom door to prevent the fumes and moisture from building up. Then turn on your fan. If you have a window in your bathroom, open it as well. While you’ll be using a natural cleaning solution, it’s still strong and will release fumes that you’ll want to air out.

If you don’t own a dedicated scrubbing brush, you can use the rough green side of a kitchen sponge. Never use steel wool or any similar material to scour a porcelain tub. Even though porcelain is scratch-resistant, this can be enough to cause permanent damage to the finish.

How to Clean a Fiberglass Shower?

/in /by

Stepping into a dirty shower can make it hard to feel clean. While it may seem like your fiberglass is ruined forever, cleaning your shower is actually a simple process. All you need to restore the shine to your fiberglass shower are a few common household products and time for them to work.

Apply the cleaning solution to your shower. Spray your vinegar-detergent mixture onto the shower and tub surfaces. Allow it to set for 10-15 minutes so that the ingredients have time to penetrate the dried on soap scum, mildew, and mineral deposits. If your shower doesn’t have soap scum, mildew, and mineral deposits, then you don’t need to let the product set.

Use a sponge, cloth, or soft-bristle brush to work in the product. Scrub your shower surfaces with your non-abrasive applicator, paying special attention to areas with thicker grime. As you clean, apply additional cleaning solution as needed. For example, if your cleaner dries before you get to that section, you can apply additional cleaner. Do not scrub with hard-bristle brushes, scouring pads, or metal pads because they will scratch your fiberglass.

Rinse with cold water. Use a cup to splash cold water onto all of the surfaces to remove the cleaning solution and the grime. You will likely need to rinse areas more than once to remove all of the product. If you have a handheld shower head, you can use it instead of a cup.

Spray the solution onto your shower and rub it in with a damp cloth. Coat the walls and basin of your shower with the solution and rub the solution in a small circular motion. Continue to work around your shower in small circles, concentrating on any built up mildew or dirt.

How Removing Stubborn Soap Scum?

/in /by

Make a baking soda paste. Pour 1 cup (237 milliliters) of baking soda into a bowl. Add a few drops of water at a time, blending until you have a paste. Your paste should be spreadable but still sticky enough to stick to shower surfaces. Alternatively, you can sprinkle baking soda directly on the soiled area then spray it with vinegar in a spray bottle.

Let it sit for 15-20 minutes, then scrub the fiberglass with a cloth or sponge. Apply the paste to stubborn soap scum. Smoothe on a generous amount of the paste to any remaining soap scum, which includes tub rings or rings around the drain in your shower pan. Pretend you are icing a cake. Your paste should be spread on in a thin layer.

Allow the paste to sit for 30 minutes. The baking soda needs time to break down the soap scum. While it dries, avoid spraying water or other cleaners in the shower. Scrub the shower with a sponge, cloth, or soft-bristle brush. Add a little water to the paste to re-moisten the baking soda. Make tight, circular movements with your scrubber as you work in the paste.

Wash away any remaining paste. Use your cup to splash water onto the paste. With a clean cloth, wipe away the baking soda. Rinse the cloth frequently to remove the baking soda residue. When all of the baking soda is gone, do a final rinse with cold water. If you have a handheld shower head, you can use it instead of a cup.

Rinse the shower. Use a showerhead or a bucket of water to rinse the entirety of the shower down, including the walls. It’s important that you remove any leftover soap or it may sink into the marble and create stains later.

How Submerging the Shower Head in Vinegar?

/in /by

Disconnect the shower head from the shower. Check the instruction manual of your shower if you do not know how to do this. Many shower heads will simply twist off, but yours may be different. If you have recently installed a new shower head, and it has a warranty, make sure you handle it according to package instructions.

Pour white vinegar in a tub. Find a container or tub large enough to fully submerge your disconnected shower head. Pour enough white vinegar into the tub to completely immerse your shower head. Pour some baking soda into the tub. You should pour in about ⅓ of a cup of baking soda for every cup of vinegar that you pour into the tub. The solution should bubble.

Put the shower head in the tub of vinegar. Completely immerse your shower head in the tub of vinegar. Make sure that it will stay submerged for at least an hour. Wait one hour. Leave your shower head soaking in the vinegar. You can also leave your shower head there overnight, if you want more of a deep clean.

Rinse the shower head. Pour water from the sink onto your shower head. Rinse off the excess vinegar and wipe clean with a cloth. Turn on your sink faucet. Allow a strong stream of water to go through the pipe attachment into the nozzle. Let it run for 30 seconds. Reconnect the shower head. Turn on your shower. Let your shower run for a few minutes to get rid of any vinegar that might still be inside the shower head.

Wipe off excess sealer on the surface of your shower. Use a dry absorbent cloth to remove any excess sealer that pools on the top of your shower. Any excess sealer that’s pooled on the surface of your marble or that has not been absorbed must be removed for the health and appearance of your marble, as leftover sealer can stain it.

How to Clean a Shower Head?

/in /by

It’s important to clean your shower head because mineral deposits from water build up in the holes of the shower head. These minerals will clog your shower head and prevent water from flowing to its full potential. There are a few different ways to clean your shower head, but they all involve vinegar, which will free up the minerals and clean your shower head best.

Put white vinegar in a plastic bag. You should pour in enough to completely cover the shower head when you tie the bag onto the shower. Make sure that the bag is free of holes and can support the weight of the vinegar for an extended period of time. Pour some baking soda into the bag. You should pour in about ⅓ of a cup of baking soda for every cup of vinegar that you pour into the tub. The solution should bubble.

Raise the plastic bag up to the shower head while it’s still connected. Hold the plastic bag open in your hands. Raise it up to the shower head so that the shower head is completely submerged. Tie off the top of the bag. You can use a zip tie, a rubber band, or even a hair elastic. Make sure that the bag is tied such that you can let go without the bag falling.

Wait at least one hour. You can also leave the bag of vinegar overnight for a deeper clean. The more time you leave the shower head soaking, the cleaner it will get. Remove the plastic bag. Throw away the vinegar and the plastic bag. Run the shower for a few minutes, until it does not smell like vinegar anymore. Your shower should be cleaner and run more efficiently!

Dry the shower. Use an absorbent rag or squeegee to dry off your shower completely. You should dry down your shower after every use, but doing a more extensive cleaning with a mild dish soap and water two to three times a week should keep the marble looking clean and fresh.