Bathtub cleaning and maintenance
The use of bathtub is very popular, many family bathrooms will have a bathtub, in modern fast, high pressure of life, to ease fatigue, relax the body and mind is not a bath in a hot bath in the bathtub. Yes, the bathtub does bring us boundless comfort.
The daily cleaning of bathtub can be done with general liquid detergent and soft cloth, not by washing with ketone or chlorine water. Disinfectants containing formic acid and formaldehyde are prohibited during disinfection. If there are scratches or cigarette burns on the surface of the bathtub, polish them only with 2000# water abrasive paper, then apply toothpaste, and polish with soft cloth. The scale on the surface of the bathtub can be rubbed with soft towel with light acid detergent, such as lemon juice and vinegar.
Hydraulic friction device cleaning: 40 degree C hot water filled with bathtub, 2 grams per liter to add cleaners, start hydraulic massage for about 5 minutes, stop pump drainage, and fill up with cold water, start hydraulic massage for about 3 minutes, stop pump drainage and clean the bathtub. The surface of the cylinder is dirty. Wipe it with wet towel and neutral detergent. This process can be repeated three times, and it will be bright and clean. Do not use hard objects or blade to strike the surface of the bathtub. At the same time, cigarette butts or heat sources above 70 degrees C should not be allowed to touch the surface of the bathtub. Do not use rough surfaces and utensils, clean cylinder surfaces containing chemical solvents or particles. When backwater and nozzle are clogged with impurities such as hair, they can be screwed down.
Do not use more than 80 degrees of hot water, such as repeated use of hot water will reduce the service life of the cylinder, the correct way is to put cold water before putting hot water. Do not start the water pump in the bathtub without water. In hydraulic massage, avoid debris or other articles blocking the backwater outlet, causing too much water pump overload, causing the pump to overheat and burn up the pump.
Nowadays, the baths on the market are mainly acrylic, steel plate and cast iron, of which the sculpt of the Alex bathtub is rich, the heat preservation effect is good and it is easy to clean, but the hardness of its surface is low and the surface is easily scratched. Although the steel bathtub is smooth on the surface, it is not resistant to impact, so it is easy to be cracked. And cast iron bathtub is more heavy, in the process of handling is easy to be hit out of the crack, and no matter what the bathtub, after the use of a long time, there will be a variety of conditions. Because of the high cost of the bathtub, the sale value on the market is also high, so facing a series of problems, generally will not be replaced, but to carry out the bathtub maintenance.
Bathtub maintenance is aimed at different faults. The common faults of the bathtub include: the bathtub can not be flooded; the bathtub is leaking; the bathtub is not energized or the leakage switch is switched off. Can’t adjust the size of the bathtub massage water. The bathtub control panel cannot start. This is the most common fault of the bathtub. The bathtub is not energized or the leakage switch is switched off. The size of the bathtub massage water can not be adjusted according to the failure of the massage bathtub. Different malfunctions require different maintenance methods.
The method of maintenance of the bathtub is corresponding to the fault, in which the bathtub does not water in general is the faucet and the foreign body is blocked, so the maintenance method is to clean the foreign body; the maintenance method of the bathtub leakage is to check the spool of the faucet valve spool and the seal ring. Then the replacement can be done; the massage bathtub is not energized, usually due to the poor contact of the power cord or the leakage of the power circuit, and the corresponding maintenance can be done. If the hydraulic size of the massage bathtub can not be adjusted, it is very likely that the suction of the pump is not enough, it needs to be checked and repaired, or the nozzle is blocked, and the dredging can be restored to normal.
The causes of the cracks in the bathtub are divided into cold cracking, thermal cracking and impact cracking. If the crack is serious, it is suggested that the professional should be invited to repair it; for the small cracking, the adhesive of the corresponding bathtub material can be used to bond, of course, to choose the nontoxic and harmless adhesive to the human body. After cleaning the bathtub and wiping dry, you can use the glue. After it is dry, it can be tested to see if the water is leaking. If it doesn’t leak, it can be put into normal use.
