Posts

The Knowledge of Bathroom Caulk

/in /by


Let this solution dry fully before applying the new caulk. Leaving it overnight and keeping it well-ventilated is best. Get rid of any small ridges left by the tape by smoothing the caulk again. Use a damp paper towel or lint-free rag again to smooth over the caulk. This will ensure that the whole caulk edging is seamless.


Focus particularly on areas where 2 pieces of tape met, and these leave a small ridge. Let the caulk dry for at least 48 hours before using the tub. The specific amount of time that it will take for the caulk to dry will be listed on the instructions on the caulk tube. Keep the area well ventilated and dry as the caulk cures.


You will be able to tell when the caulk is dry because the consistency will change to look firm rather than wet, and it will be completely dry to touch. Let the cleaner sit for 5-10 minutes. After a few minutes, the dingy messes that have built up on the surface of your acrylic shower will begin to dissolve. This will allow you to wipe them away with ease.


If you’re dealing with particularly heavy soap scum or stains, it may help to reapply the cleaner once or twice. Use this time to take care of any other cleaning tasks you need to complete, like detailing the faucet or shower head.


Rinse and wipe out the shower. Turn on the shower head and direct the flow of water over the areas of the acrylic you just sprayed. Wash away as much liquefied grime and cleaning solution as you can. Once you’ve given the shower a preliminary rinse, go over the acrylic using a soft microfiber towel or sponge to remove any remaining residue. For stubborn residue, use an old toothbrush to scrub it away.

How Using Vinegar and Water?

/in /by


Mix together vinegar and water. Ordinary vinegar makes a versatile cleaning solution that’s both safe and all-natural. Combine equal parts distilled white vinegar and warm water in a small spray bottle. Shake the bottle to make sure the two liquids are thoroughly blended.


The heat from the water will be even more helpful for releasing dried stains from the surface of the shower. For even better results, add a few drops of mild liquid dishwashing detergent. The soap will emulsify dirt and oil while the vinegar brightens and disinfects.


Treat problem areas with the vinegar solution. Mist the inside shower with the vinegar solution. Be sure to address spots with the worst buildup. This may include unexpected places like the shelving at the top of the shower or the area around the drain. Don’t forget to get inside cracks and crevices and along recessed panels and soap dishes. Pure vinegar makes the perfect antidote to mold and mildew growth.


Leave the vinegar to break down stains. Vinegar is an effective natural solvent, but it requires a little time to work effectively. For most light or moderate messes, the vinegar should sit for at least half an hour. To remove heavier buildup, you may even want to let it remain for 1-2 hours to ensure success.


If vinegar alone isn’t cutting it, sprinkle a little baking soda over the affected area before spraying it again. The foaming action produced by the two cleaners will eat away at stubborn gunk and grime. A mixture of hydrogen peroxide and cream of tartar can make a convenient substitute for baking soda and vinegar.

How to Clean a Fiberglass Shower?

/in /by

Stepping into a dirty shower can make it hard to feel clean. While it may seem like your fiberglass is ruined forever, cleaning your shower is actually a simple process. All you need to restore the shine to your fiberglass shower are a few common household products and time for them to work.

Apply the cleaning solution to your shower. Spray your vinegar-detergent mixture onto the shower and tub surfaces. Allow it to set for 10-15 minutes so that the ingredients have time to penetrate the dried on soap scum, mildew, and mineral deposits. If your shower doesn’t have soap scum, mildew, and mineral deposits, then you don’t need to let the product set.

Use a sponge, cloth, or soft-bristle brush to work in the product. Scrub your shower surfaces with your non-abrasive applicator, paying special attention to areas with thicker grime. As you clean, apply additional cleaning solution as needed. For example, if your cleaner dries before you get to that section, you can apply additional cleaner. Do not scrub with hard-bristle brushes, scouring pads, or metal pads because they will scratch your fiberglass.

Rinse with cold water. Use a cup to splash cold water onto all of the surfaces to remove the cleaning solution and the grime. You will likely need to rinse areas more than once to remove all of the product. If you have a handheld shower head, you can use it instead of a cup.

Spray the solution onto your shower and rub it in with a damp cloth. Coat the walls and basin of your shower with the solution and rub the solution in a small circular motion. Continue to work around your shower in small circles, concentrating on any built up mildew or dirt.

How to Clean Tough Stains from a Bathtub?

/in /by


Nobody likes the thought of taking a soak in a dingy bathtub. With constant exposure to moisture, bacteria and mold can collect on the walls of your tub, creating a mess that’s both unsightly and unsanitary. Being diligent about keeping your bathtub clean is the best way to prevent dirt and gunk from getting out of hand, but sometimes you’ll have to bring out the big guns to chip away at heavy, set-in stains. Fortunately, this can usually be done with the aid of a few basic household products and a little elbow grease.


The longer you let the solution sit, the more effective it will be at lifting long-settled residue. Wear gloves and work in a well-ventilated area when handling chemical cleaning solutions. Scrub out the stains gently. Use a soft sponge or microfiber towel to avoid leaving marks or scratches. Go over the stains using a gentle circular motion. When you’re finished, rinse away any remaining dirt and cleaning solution and let the tub dry completely.


If necessary, apply another burst of cleaning solution. Wipe and repeat until the stains come out of the enamel finish. Using anything more abrasive than a sponge to scrub enamel may wear down the finish.


Add enough water to produce a paste. Spray purified or ordinary tap water onto the cleaning powder. With the addition of moisture, the powder will take on a thick, foamy consistency. Rub this paste into the stains and give it about half an hour to take effect. You can also wet a clean sponge or washcloth and use it to rub in the cleaner until it thickens.


Another option is to wet the tub before you apply the cleanser. Spray the tub with the shower head or fill a cup with water and pour it around the inside of the tub. Be careful not to add an excessive amount of water. The cleaner won’t be as effective if it’s too thin.

How Removing Stains from an Enamel Bathtub?

/in /by


Try cleaning with vinegar first. Though it’s a mild natural cleanser, vinegar will typically be potent enough to deal with most stains when applied heavily and given time to set up. Spray the tub down thoroughly, let the vinegar sit for a few minutes, then scrub aray the stains using a sponge or stiff-bristled brush. If you discover that vinegar isn’t having the desired effect, you can move on to more intensive methods. There will come a point when simply adding more and more vinegar won’t suffice.


Use a bleach-free commercial cleaning spray. Products like Lysol All Purpose Cleaner, Kaboom, Shout! and Scrubbing Bubbles shower cleaner are good for eating away at tough stains without damaging delicate surfaces. Since most of these products contain a similar combination of ingredients, any of them will work as well as another. Just make sure whatever product you choose doesn’t contain bleach, as this can severely weaken the outer enamel layer of the tub.


Only buy cleaners that have been approved for use on enamel-coated bathroom surfaces. Be sure to check the label carefully before buying a particular cleaning product so you’ll know you’re getting what you need. If possible, open a nearby window, open the door, and turn on a fan to ventilate the bathroom while you clean with any of these products.


Make your own natural cleaner. If you’re reluctant to go shopping, you can formulate a simple all-purpose bathroom cleaner at home by mixing together warm water, baking soda, Castile soap and essential oils in a spray bottle. All of these ingredients are readily available and safe to use but are quite potent when brought together. Once they’re combined, spray the mixture onto the stained surface and give it a few minutes to take effect before wiping it away.


If you’re having trouble tracking down Castile soap, hydrogen peroxide will make an acceptable substitute. Essential oils like tea tree and peppermint can also act as natural disinfectants. Soak problem areas for several minutes. Mist on the solution and give it a chance to sit. Pay special attention to places with heavy staining and discoloration. The cleaning solution should get to work dissolving these stains right away.

How Removing Stains from an Acrylic Bathtub?

/in /by

Avoid abrasive chemical cleaners. When cleaning an acrylic bathtub, stay away from harsh astringent powders such as Comet and Ajax, as well as harsh chemicals like bleach. Acrylic is a soft material and is therefore easily damaged. These types of products are almost guaranteed to ruin your tub’s finish. It’s generally a good idea to start with the gentlest cleaning solution available to you and work your way up to more powerful options if that doesn’t work.

Spray the stains with vinegar. Distilled white vinegar makes an excellent natural cleaning solution, especially on smooth surfaces like acrylic that release stains easily. Fill a spray bottle with vinegar and keep it on hand for routine bathroom cleaning tasks. Apply the vinegar liberally to completely cover the affected area. Lemon juice makes a fine alternative to vinegar if you happen to have some in the refrigerator.

Allow the vinegar to sit for 10-20 minutes. As it sits, the acidity in the vinegar will break down mold, grime and discoloration so that they can wiped away with ease. You may even see stains begin to dissolve and run off on their own, before you even begin scrubbing. Make sure you give the vinegar ample time to begin working. For especially troublesome spots, sprinkle a little baking soda onto the vinegar as it soaks.

How Cleaning Your Shower Walls and Tub?

/in /by

Empty your shower. Remove bottles, loofahs, razors, soap, and other items. Wipe down plastic items to remove mildew and excess water. Throw out empty bottles and items you aren’t currently using. Having too many items in your shower makes it harder to keep your shower clean.

Rinse your shower walls and tub. Using a bucket or cup, splash the shower walls and tub with hot water. If you have a handheld shower head, they work very well. You don’t need to be perfect with this step; you just want to get all the hair, dirt, and other particles down the drain and out of your way. Rinse your walls and tub once a week between deep cleanings to maintain cleanliness. For best results, use a cleaner that helps prevent mildew and soap scum. Deep clean your shower and tub once a month.

Open the bathroom door. If you have a window, open it as well for extra ventilation. Cleaning products can be dangerous if you inhale them, so leave the room if you start to feel lightheaded or nauseous. If your bathroom has a fan, turn it on to help with ventilation.

Divide your shower wall into three to four sections. Mentally divide your shower so that you can make your cleaning task more manageable. Cleaning in sections will prevent the product from drying before you have a chance to work it into the surface. If you have a bathtub, include it in your sections.

Spray the first section with a cleaning agent. Let it soak for 5-10 minutes, unless the package recommends a different amount of soak time. Make sure that your cleaning agent is appropriate for the type of material that your shower is made from. Never use acids like vinegar, ammonia, and normal bathroom cleaners on marble. Only use products that are labeled for use on marble. Make your own cleaning agent by mixing 1 cup (237 milliliters) of vinegar, 1/2 cup (118 milliliters) baking soda, 1 cup (237 milliliters) ammonia, and 1-1/2 gallons (5.5 liters) of hot water.

bathroom maintenance coup bath cleaning and maintenance

Bathroom Maintenance Coup: Bath Cleaning And Maintenance

/in /by

bathroom maintenance coup bath cleaning and maintenance

Newspaper cleaning law

The newspaper, for the removal of dirt and hair, the surface of the newspaper, now many people should have, it is also a kind of clean easily, put some hot water in the bathtub, and then open the newspaper, put in the bathtub, floating in the water, after a period of time, the newspaper has hair out gently, dirt and newspaper.

Two, silk stockings cleaning law

Silk stockings very easy and convenient, clean, can also avoid the wear clean stockings melted into a ball, wipe the surface gently, this method what benefits? Silk stockings are very thin, will not scratch the surface, and no detergent.

Three, liquor cleaning law

White alcohol, can remove dirt, can also remove the odor, the fine liquor is diluted with water, and then spray and wipe again in the bathtub,deep dirt, first with a brush dipped in clean white alcohol, no matter when, to maintain ventilation, it can also shed.

Four,  routine maintenance method

Bathtubs should be cleaned not only in time, but also in daily use. When cleaning, use a neutral detergent, and the tools should be soft, clean and dry. Don’t put anything metallic in the bathtub, or rust will contaminate the bathtub.