Purchase an enzymatic drain cleaner to dissolve hair. Purchase a drain unclogging formula that is specifically made to dissolve hair and soap scum. Typically, these types of solutions contain bacteria like bacillus that is intended to feed on hair. Enzymatic drain cleaners are also gentle on pipes and bathroom surfaces.
Check the ingredients list. Caustic drain cleaners made with sodium hydroxide (and other alkaline ingredients) will dissolve soap scum but not hair. While most enzymatic drain openers are free of harmful toxins, always check the label to see if you need to wear protective clothing.
Wear protective clothing, if necessary, before opening the bottle. Refer to the instructions on the bottle about whether or not you need to protect your eyes and skin. If you’re not sure, better to be safe and wear glasses and gloves anyway. If you don’t have protective goggles, sunglasses will work just as well.
Stand outside the shower and pour the cleaning solution down the drain. Pour a slow and steady stream of the solution down the drain until half or all of the bottle is gone. You don’t need to remove the drain stopper. Refer to the instructions on your particular cleaner to see how much you should use. For heavily clogged drains, you might want to use the whole bottle.
Make sure there is no standing water in the shower or tub. If there is, wait until it has drained away before you pour in the formula. Let the unclogging formula sit for 2 hours or for the recommended time. Allow at least 2 hours for the drain opener to dissolve all the hair and grime in the pipes. Refer to the instructions on the bottle to see how long the manufacturer says to let it sit.
https://baranasanitary.com/wp-content/uploads/2020/01/Dissolving-Hair-with-Chemicals-1.jpg7501150adminhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadmin2020-02-03 08:00:042020-01-15 08:44:07How Dissolving Hair with Chemicals?
Decide what your tray will hold. First, think about what you intend to keep on your tray during baths and how much space each object will need. Make sure that you use a piece of lumber that is wide enough to hold everything. Allow extra space so nothing is sitting on the edge of the tray. For example: A 1” x 10” (2.5 x 25 cm) board should be wide enough to hold a book, candle, and glass with room to spare.
However, be aware that lumber sizes (such as 1” x 10”) refer to when the wood is freshly cut before it dries out and shrinks. So, if you have something wider than 10 inches that you want to place on your tray, you will need a wider board than a 1” x 10”. Choose how many layers of wood you will need. Decide between making a simple tray with no raised surfaces or one with holders for certain objects.
For the simplest tray, plan on using a single piece of lumber. Or, to minimize the risk of spilling stuff into the tub, purchase a second piece of equal size to create holders before attaching it to the base board. Alternately, you could rim the entire tray by screwing smaller pieces of lumber, like a 1” x 2” (2.5 x 5 cm), around all four edges of the base board instead of creating individual holders.
Line the tray with wood trim on each side 1 to 1.5 in (2.5 to 3.8 cm) wider than the tray to have an attractive raised lip. Use a piece of plexiglass as the base layer and a piece of wood the same size on top with holders cut into it. The plexiglass is easy to clean, waterproof, and it will protect the wood.
Measure your tub. Use a measuring tape to determine the width of your tub. Be sure to include the rim on either side, since this is where your tray will rest. Also double-check that the rim on either side is level with each other. Surround units (where the tub and the shower stall are all one unbroken piece) may incorporate designs without a level rim on the inside of the stall.
https://baranasanitary.com/wp-content/uploads/2020/01/Designing-Your-Tray-2.jpg7501150adminhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadmin2020-01-15 08:00:342020-01-08 08:55:38How Designing Your Tray?
Fix any leaks you can see. If a leak is causing the problem, it’s time to take care of that! Replace leaky faucet heads, for instance, or if the leak is more than you can handle, call in a professional to find and fix the leak. If you don’t fix the leak, the mold will just return.
Spray the area down with vinegar after every shower. To help prevent the mold from coming back, keep a spray bottle in your bathroom. Then, spray down the walls and tub after you get done with your shower. The vinegar will help kill the mold spores. If the smell bothers you, add a few drops of essential oil, such as peppermint, citrus, or tea tree oil, to help cover up the scent.
Air out the bathroom after you shower. If you have an exhaust fan, use it. If you don’t, make sure to keep the door to the bathroom open after you shower so the air can dry out. Too much humidity in a small space can lead to mold. If you don’t have an exhaust fan, try placing a fan in the door to blow the air into the rest of your home.
Clean the bathroom once a week. Use a disinfecting cleaner to go over your shower and scrub it down. Pick a day to do it each week to make it easier to remember, and set up a reminder if you forget. Make sure to change out your sponge or cleaning brush regularly, as it can grow mold, too.
Use your air conditioning in the summer to keep the humidity low. Pulling humidity out of the air is one of your AC’s main jobs, so you should run it in the summer when it’s humid out. If you don’t have an AC, try using a dehumidifier to reduce the humidity. If possible, keep the humidity in your home under 60%.
Your bathroom should be a comfortable space that is also functional and easy to use. Designing a bathroom to suit your needs requires an attention to detail and a practical approach to the space. Start by determining the layout of the bathroom. Choose the bathroom fixtures, like the toilet, the sink, and the shower or tub, as well as accessories like storage baskets, shelving, and a mirror. Then, create a design plan for the bathroom so you can build it to suit your needs.
Get woven storage baskets for bathroom items. To add more storage to the bathroom, look for deep woven baskets that you can slide under the sink. Put toiletries, spare toilet paper rolls, and other items in the baskets. You can also use large storage baskets to store extra towels.
Add shelving above the toilet or sink for storage. Another option is to install shelves above the toilet for candles, toilet paper, and other items. Make sure the shelves are just as long as the toilet and not too wide so they do not extend too far over the toilet. Shelves above the sink are a good option for extra storage as well. Try having one long shelf that is not too wide so you can still use the sink. You may want to put a shelf between the sink and mirror to store toothbrushes and soap to keep the countertop clear.
Put in a mirror to make the space seem bigger. Include a mirror over the sink so people can see themselves when they get ready for the day. It will also help to keep the space more open. The mirror should be as wide as the sink. If you don’t have room for a mirror over the sink or vanity, install one on the back of the bathroom door. A full-length mirror would work well here.
Include a chair or a bench if there is room. A chair by the sink or close to the door can provide some seating in the bathroom. A bench is a good option if the bathroom is going to be used by multiple people at once and you have the space for it. Choose wooden, metal, or plastic seating. If you go for an upholstered piece, make sure it is water- and mold-resistant. Make sure the chair or bench does not crowd the room or make it feel too small.
https://baranasanitary.com/wp-content/uploads/2018/09/How-to-choosing-Bathroom-Accessories-900600.jpg600900adminhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadmin2018-09-05 06:50:312019-07-31 07:42:46How to choosing Bathroom Accessories?
With the shape of a person like, look at the toiletexterior and exterior surface of the glaze is bright, glittering and translucent, whether there are ripple cracks, eye impurities, appearance symmetry, on the ground is stable and not swinging. Pay attention to the selection of toiletporcelain, porcelain delicate, glazed smooth and dense toilet, water and dirt is not easy to infiltrate, easy to clean, both beautiful and easy to clean. At present, the high-end toiletporcelain is also treated with nano glaze, which is easier to handle.
In the choice of water saving toilet, we should understand the principle of water saving, for example, some products are 6/3 double button double punching tank, there is no pressure device inside the tank, it can effectively solve the contradiction between water adding and rinsing. The flush mute of the toilet may be mute, but it is also a good strategy to reform the way of flushing. The siphon jet flush toilet reduces the noise and increases the effect of the rinsing.
The height of the water seal of the toiletis the key to prevent the smell from returning. The small seal less than 50 millimeters is easy to return and is not suitable for use. Check whether the water in the water tank is a factory product, whether it has 3, 6 liters of water-saving function, water tank, the inside of the pipe is not glazed, knocking any part of the toiletto listen to its sound is crisp.
Before buy toilet, we must make clear the exact size of the lower water inlet center from the wall, which is generally divided into 300, 400mm pits, and how much the length of our home is not understood. The toiletoutlet is divided into two types, called the front outlet toiletand the rear outlet toilet. The front water toiletis suitable for large wall distance. The quality of the accessories is the guarantee of the durability of the toilet. Most of the toilet parts are made of plastic, the quality is uneven, the quality of all copper fittings is good, and the beauty is not easy to be aged.
The famous brand store of famous bathroom is not only arranged in neat and beautiful, but also usually with a sample room, which puts the qualification certificates which can prove their strength in a more obvious position. Whether the glaze of the toiletis uniform, there is no obvious color difference and deformation, glossiness is bright enough, there are obvious brown eyes, pinholes, spots, cracks, orange glaze, ripples, blotches, falling dirty and so on. If the toiletglaze quality is not good, it is easy to make the dirt hang on the four walls, and the good glaze is smooth, delicate, without defects. After repeated rinsing, it can still be as smooth as new.
The quality of the glazed surface and the green body of the toiletis very fine, and the hand feels the surface without the slightest bumpy feeling. Some of the lower and middle toiletsare glazed, glazed and billets are rough, and pores can be found in the light. To observe the glaze of the reverse bend of the toilet, to reach the mouth of the toiletin the toilet, to touch the smoothness of the inside, and to extend far and far. The smooth inside is a good product, which prevents dirt and clogging and is not easy to leak.
The high grade toilet adopts high-grade ceramics, the sintering temperature of this kind of ceramic is above 1200 degrees, and the requirement of all porcelain of sanitary ware is reached, and the hand has a heavy feeling. Middle and low gear is used in the sanitary ceramics medium and low temperature ceramics, these two kinds of ceramics because of its low burning temperature, burning time is short, so it can not meet the requirements of all porcelain.
The most obvious difference between high temperature ceramics and medium and low temperature ceramics is water absorption. The toilet heated by high temperature will not suck into the sewage crack, and will not smell any more. And some medium and low temperature ceramic water absorption rate is very large, so it is easy to enter the sewage, and it is not easy to clean the smell of the strange smell, long time will also happen to crack and leak phenomenon.
The main function of the toiletis flushing, and the most important factor affecting the flushing is whether the piping design is scientific and reasonable. Therefore, the general regular shop has a water test station for customers to test the water. In the normal standard, the requirement is less than or equal to 6 litres of water, three flushes, an average of at least five water-filled table tennis flush out.
When most people are in the shower, they find that the longer the shower head is used, the smaller the water flow is, that is because the maintenance of the shower is not noticed and the shower head is blocked. The shower head is not installed for a long time, but it is blocked by the head. This may be caused by the poor quality of your shower head. But if your shower head has been installed for a long time, use long time, meet the shower head blockage, this is due to the long time water spray head, the impurities in the water will accumulate into the shower head, long time will cause the shower head blockage, belongs to the normal situation.
If it is due to the poor quality of the shower head, it is necessary to pay attention to the quality of shower head when choosing and choose a qualified shower head. In general, it is necessary to buy regular and large-scale commodity inspection, and can not greedy for small cheapest, choose the shower head of plastic and other products, and the shower head of copper should be selected to prevent the quality problems such as plugging and cracking in the shower head.
If it is caused by the long time use of the shower, we need to clean the shower head regularly in our daily life. Generally, we can use white vinegar to remove scale: Every three months to carry out a cleaning work, the shower head is dismantled, soaked in a basin with white vinegar, time is about 4-6 hours, then the spray head clean, installed back, in the water after the scale will be outflow, so that the cleaning of the scale, the elimination of fine bacteria effect.
Manual cleaning needs to remove the net cover of the flower spray, or remove the other scale from the scale and clean it with the brush before installing it back to its original place. Some flower shower head sprinklers will be equipped with some special dismantling tools at the time of purchase, so that they can be conveniently used by consumers. Some of the outflow of its outlet is used in the design of rubber particles, its touch is comfortable, soft, not fouling, but also very convenient to clean, as long as the fingers are used to light the particles will be able to clean the scale. This is the cleaning method chosen by using the characteristics of materials. It is a popular way of cleaning in the market. Many of the shower head are made up of special structures. They can be cleaned automatically when they are used. Flower shower head with cleaning needles, which do not need manual cleaning, can bring out the scale. It is very convenient.
Apart from paying attention to cleaning, we should also pay attention to the daily maintenance of its surface. When we need to use it, keep its surface clean, usually soft cloth, dip the flour to wipe its surface, rinse with clean water to keep its surface clean and prolong its service life. Regular cleaning, white vinegar can be used to soak and rinse the surface and interior of the shower head, and then use cotton cloth as the outlet of the shower head to clean it. This can not only reduce the impact of the scale on the spray, but also play the role of sterilization and disinfection.
For the surface of the shower head, it can be cleaned regularly with flour and rinsed with water, so that the surface of the shower head can be as bright as new. When cleaning the scale, remember not to use strong acid to clean it, otherwise it will easily damage the surface of the shower head. Do not disassemble and maintain the shower head itself, and prevent incorrect methods from damaging the appearance or internal structure of the shower head. The use of the daily use of the environment should not exceed 70 degrees, otherwise it is easy to reduce the life of the shower head, therefore, the installation of the spray should be far away from the electrical source.
https://baranasanitary.com/wp-content/uploads/2018/07/Precautions-for-the-maintenance-of-the-flower-shower-head-900600.jpg600900adminhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadmin2018-07-06 06:35:452019-07-31 07:54:38Precautions for the maintenance of the flower shower head
Do you know if you understand the wall mounted bathroom cabinet, bathroom cabinet wall mainly by the wall hanging, both open, put common objects, and closed the drawer can be placed, easy to damp things, small and practical, so what are the advantages of wall mounted bathroom cabinet?
As long as the bathroom space, bathroom cabinet is much bigger than the practical column: first, the bathroom has a lot to receive, there is a cabinet, can put things inside out of order; secondly, there is a table around the basin, you can easily put a lot of activities. At least one of the basins at home should be large and deep, so that clothes can be easily cleaned. Bathroom counters should be bigger as possible.
If necessary, to the bathroom cabinet above the cabinet with a mirror, and can add a lot of storage space. In order to make the best use of bathroom space, custom bathroom cabinet is a good choice, and can let the cabinets do business to you together, not only the price will have some benefits, but also style and family unity.
https://baranasanitary.com/wp-content/uploads/2017/09/what-are-the-advantages-of-wall-mounted-bathroom-cabinets.jpg600900adminhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadmin2017-10-08 09:55:052019-08-21 08:24:20What Are The Advantages Of Wall Mounted Bathroom Cabinets?
Water is indispensable to our daily life quality of life, a good faucet can be used for many years, a poor quality faucet can be easily broken, faucet although small, but in the Home Furnishing in status is important, any family every day without water, always close frequent contact with small faucet.
Look at the surface of the Basin Faucet: the coating is brilliant
After the basin faucet is polished and cast, the surface should be nickel plated or chrome, in order to prevent the basin faucet from oxidizing. After the nickel plating or the chromium, the middle pot hydrochloric acid test should be carried out on the water tap of the basin. After the test, the coating should be free of rust at a certain time. It is understood that only through the neutral salt spray test basin faucet can leave the factory.
When consumers buy, the best faucet placed in a well lit place upon the faucet surface should be bright as a mirror, without any signs of burning, oxidation spots, no pores, no bubble, no leakage, uniform color plating; touch no burr, sand; pressing with a finger tap, fingerprints quickly spread. And it is not easy to dirt.
Turn the handle of the Basin Faucet: supple and relaxed
The valve core of a common basin faucet has a steel ball, a valve core and a ceramic valve core. The steel ball core has good resistance to pressure, but the disadvantage is that the rubber ring which is sealed can be easily damaged and will soon be aging. Compared with the steel ball valve, the ceramic valve core is more heat-resistant and wearable, and the ceramic valve itself has good sealing performance, so the high resistance can be achieved, and the water leakage of the faucet is not caused by the abrasion of the valve core. With ceramic valve head, the handle is more comfortable and smooth, and opens and closes quickly.
As the valve core in the basin faucet, consumers can not see the valve when buying, but consumers can handle the handle to determine the spool is good or bad. Generally speaking, consumers on the upper, lower, left and right rotation handle, if feel light, no blocking feeling, it shows better spool.
https://baranasanitary.com/wp-content/uploads/2017/09/how-to-choose-basin-faucet.jpg600900adminhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadmin2017-10-03 02:32:482019-08-21 08:22:03How To Choose Basin Faucet?
