Posts

How to Clean an Acrylic Shower?

/in /by


If the highlight of your morning is stepping into a hot, revitalizing shower, chances are you’ve put some thought into the best way to keep your bathroom sanctuary sanitized and sparkling. Luckily, newer showers and shower liners made from synthetics like acrylic are a breeze to clean. That being said, acrylic is a soft material that can easily be scratched or discolored, so it’s important to make sure you have the right tools for the job to avoid causing permanent damage.


The key to cleaning acrylic safely and effectively is to use a mild acid-based solution, followed by a wipedown with a non-abrasive cloth. All-Purpose清洁剂或Bar Keeper’s Friend. Choose a non-abrasive cleaning solution. Acrylic is a soft, malleable finish, which means it can easily be scratched or marked up if you’re not careful. To prevent doing lasting damage to your shower, pick out a product that doesn’t contain any harsh chemicals or astringents.


Your best bet is to use a mild acid-based solution like Lysol Power Bathroom Cleaner, Formula 409 All-Purpose cleaner or Bar Keeper’s Friend. Stay away from any type of astringent cleanser, including Comet, Ajax and Scrubbing Bubbles, as well as solvents like acetone. Whenever possible, using natural derivatives to clean your bathroom will be your safest choice.


Spray the product onto shower stains. Apply the cleaner liberally to areas where grime, soap scum and hard water stains have accumulated. Focus on spots that suffer from visible dirt or discoloration. You may need to use quite a bit of cleaner in order to penetrate multiple layers of dried-on residue.


Be sure to remove all soaps, shampoos and other hygiene products from the shower before you get started so that you can clean underneath them. Pull back the shower curtain all the way and turn on the overhead fan to keep the bathroom properly ventilated while you clean.

How to Clean Tough Stains from a Bathtub?

/in /by


Nobody likes the thought of taking a soak in a dingy bathtub. With constant exposure to moisture, bacteria and mold can collect on the walls of your tub, creating a mess that’s both unsightly and unsanitary. Being diligent about keeping your bathtub clean is the best way to prevent dirt and gunk from getting out of hand, but sometimes you’ll have to bring out the big guns to chip away at heavy, set-in stains. Fortunately, this can usually be done with the aid of a few basic household products and a little elbow grease.


The longer you let the solution sit, the more effective it will be at lifting long-settled residue. Wear gloves and work in a well-ventilated area when handling chemical cleaning solutions. Scrub out the stains gently. Use a soft sponge or microfiber towel to avoid leaving marks or scratches. Go over the stains using a gentle circular motion. When you’re finished, rinse away any remaining dirt and cleaning solution and let the tub dry completely.


If necessary, apply another burst of cleaning solution. Wipe and repeat until the stains come out of the enamel finish. Using anything more abrasive than a sponge to scrub enamel may wear down the finish.


Add enough water to produce a paste. Spray purified or ordinary tap water onto the cleaning powder. With the addition of moisture, the powder will take on a thick, foamy consistency. Rub this paste into the stains and give it about half an hour to take effect. You can also wet a clean sponge or washcloth and use it to rub in the cleaner until it thickens.


Another option is to wet the tub before you apply the cleanser. Spray the tub with the shower head or fill a cup with water and pour it around the inside of the tub. Be careful not to add an excessive amount of water. The cleaner won’t be as effective if it’s too thin.

How Maintaining Your New Vanity?

/in /by

Reassemble the vanity after it’s dry. When all the pieces are dry, you can remove the painter’s tape and reassemble the vanity pieces with the hardware you stored. Re-stock it with your products, and then it’s ready to be used!

Take the opportunity to do some spring cleaning. As you’re putting items back into the vanity, think about how often you use them. If you’ve barely or never used them, get rid of them to make more space inside your new vanity.

Revamp the hardware to give the vanity a whole new look. Switch out your drawer and cabinet handles for new hardware. Try hardware in a different metal, glass knobs, or handles instead of knobs. This will complete the vanity’s transformation and make it feel brand-new.

Patch up scratches by gently sanding and painting over them. Use a very fine grit sandpaper to lightly sand the chipped area. Then use a brush with the same paint that’s already on the vanity and paint over the scratch.

Try to fill the scratch in with the paint so it looks level with the rest of the surface. Let the paint dry for a few minutes, and the vanity should look as good as new. Very fine sandpaper includes grits of 240, 320 and 400.

How Cleaning Your Shower Head?

/in /by

Pour white vinegar in a gallon-sized plastic storage bag. The amount of vinegar that you need will depend on how big your shower head is. You need just enough vinegar to cover the end of the shower head where the water sprays out. You can use any plastic bag, but a storage bag is more likely to be leak-proof. Clean your shower head once a month to keep your water flowing well and to prevent mildew.

Place your shower head in the bag. Make sure that your shower head is submerged in the vinegar. If you need to, remove the bag and add more vinegar to cover the spray area. Tie a large rubber band around the end of the bag. Place your rubber band above the shower head so that the bag stays in place while allowing the shower head to fully soak in the vinegar. If you don’t have a rubber band, you can tie off your bag with anything that will hold it in place.

Remove the bag in the morning. Let your shower head soak in the vinegar overnight. In the morning, pour the vinegar down the drain and throw away or recycle the bag. Run clean water through your shower head. Turn on your shower and make sure that the shower head is spraying at full capacity. Wait a minute before getting in the shower to ensure that the vinegar is fully washed away.

Rinse off the shower door. Use your cup or bucket to wet the shower door. This pre-rinse should also remove any debris. Rinse the door weekly between deep cleanings. Deep clean the shower door once a month. Apply a cleaner. You can use a commercial product, or you can mix a tablespoon (15 milliliters) of white vinegar into a cup (237 milliliters) of baking soda to use as a natural cleaning agent. Coat the shower door in your cleaner. Set a timer for 1 hour. Your cleaner needs time to set. While you wait, you can clean another part of your shower if you’d like.

Wipe away the cleaning agent with a soft cloth. Be careful not to use a brush or wire scrubber on a shower door, which can easily scratch. Choose a soft cloth, such as microfiber, to remove the cleaner and grime. Rinse the door with clean water. Cleanse the door until there is no more cleaning agent. Dry the door with a soft cloth. Use a clean cloth to remove the excess water. This will prevent streaking on your newly clean door.

clean bathroom 4 fine: make bathroom clean and bright

Clean Bathroom 4 Details: Make Bathroom Clean And Bright

/in /by

clean bathroom 4 fine: make bathroom clean and bright
1, the toilet

To add the right amount of water in the toilet, take the toilet brush to clean it, then pour about 5-10 ml of detergent or hydrochloric acid solution, scrub with a brush coated evenly, such as dirt heavier, can pour a little detergent soaked after brushing, and then washed with water until clean, dry clean.

2, shower head

The dirt surface of the nozzle after cleaning with pliers and unscrew the nozzle outlet interface, the filter inside the clean water nozzle is not smooth, with a needle to each outlet patiently through it, if the needle tip is sharp, and no patience with brute force to dredge it is likely the damage caused to change the direction of the water outlet.

3, bathroom cabinet

When cleaning the bathroom cabinet should pay attention to good, do not choose a dry cloth, so as not to scratch the surface, to avoid the water washing, to avoid corrosion, if the surface stains, can not use alcohol, gasoline and other chemical solvents, a better choice of neutral cleaning agent.

4, bathtub

Clean the bath generally have three methods can be used in vinegar, rag soaked in vinegar, then cover the stains on the next morning, the baking soda and vinegar tune into a paste, and then use the brush to clean, it is easy to clean; outdated old newspapers can also be used to clean the bathtub; in addition the above two, generally is the most commonly used special bathtub cleaning agent, bath can not only remove stains, and time-saving, no damage to the surface of the tub is good, clean bath method.