Posts

How Taping off the Tub?


Tape off the edges of the tub with masking tape. Some bathtubs are not freestanding fixtures and are housed within a painted housing. If your bathtub is set within a wood or plaster housing, use painters tape to tape off the edges of the tub to prevent the new bathtub reglazing from getting on anything other than the tub itself. If your bathtub is free standing, you can skip this step.


Wrap the spout, handles and anything else that’s not the tub in plastic. Everything that’s staying in your bathtub that isn’t the bathtub itself needs to be covered before you start the refinishing process. Make sure the shower head, any exposed plumbing, bath nozzle and anything else you don’t want refinished is covered in plastic. Once you cover things in plastic, use painters tape to secure the plastic in place.


Use paper or plastic to cover the walls of the shower. The walls of the shower should be covered if they’re not a part of the tub itself. You can hang masking paper or loose plastic from the wall using painters tape to secure it in place. If the shower walls are a part of the bathtub, you may want to refinish them along with the tub, rather than taping them off.


Apply a bonding agent to the surface of the tub if it’s made of iron. Iron tubs need a bonding agent to help the new finish seal in place. Some bonding agents can be painted on while others need to be sprayed on. Follow the directions on the agent you purchase closely for good results. You can buy bonding agents for iron tubs at your local hardware store.


Mix some reglazer per its instructions. Reglazer, or finish, is like a thick paint that you’ll apply to the tub to serve as its new surface. Some tub glazes come in self contained cans for you to spray on, while others are meant to be mixed and applied using rollers or paint brushes. Be sure the bonding agent is completely dry before applying the new finish.

How to Paint the Bathtub?


If your cast-iron tub is looking a little rundown, save some money and give it a new coat of paint rather than replacing it. After filling in any gaps or cracks, sanding down the interior and exterior, and giving it a few coats of acrylic urethane enamel paint, you’ll have a bathtub that looks brand new. It’ll cost you about $450 to refinish your tub yourself, versus over $3000 to replace it.


Leave the tub alone until it has cured completely. Don’t step in it, run any water, or use it it any way. Follow the paint manufacturer’s instructions for the curing time, which is generally around 24 hours. You can also use a heat lamp to speed up the curing time, but that could also cause discoloration in the paint.


Remove the masking tape and reattach the tub fixtures. Once the tub is dry, you can remove all the plastic sheeting and tape and replace the drain and faucet. Throw the sheeting and tape away. You may also want to mop the floor and give the rest of the bathroom a thorough wipe-down to catch any dust or dirt left behind from the painting process.


Re-caulk the tub before you use it again to protect it from mold. Use a caulking gun to reapply the caulk to the areas where the tub meets the shower, if that’s applicable. Follow the instructions for the brand you purchased and let it dry before you use the tub. Caulk can take 24 hours to cure, but it’s generally safe to expose it to water after a few hours.


Spray painting is generally an easier process because you won’t have to lean over the tub and risk smearing the paint. Similarly, if you’re painting the tub by hand, use long, even strokes to coat the tub’s entirety.

How Cleaning the surface of the tiles?

Clean the tile surface with a recommended cleaning product. Scrub with an abrasive rag, or rig a nylon bristle drill attachment. Pay extra attention to the bottom section, because that is usually the area with the most mildew. Rinse well. Rake the joints. Cover the drain. Carefully rake each joint with a diamond carbide rake.

Be careful not to slip, or it will leave irreparable scratch marks. The surface should be wet during this part of the process. If the grout is too solid to rake, hot water usually helps. Remove caulking with a plastic scraper. Avoid using metal scrapers and steel wool, because they will scratch the enamel on the tub.

Rinse the surface, and towel dry. Mix the grout thoroughly until it comes to a creamy consistency. Using a rubber float, apply the grout in several directions. Work in small sections so that the grout remains pliable. Make sure that the grout is packed in well. Allow twenty minutes to an hour for the grout to dry completely.

Sponge the surface. Sponge the surface of the tiles until the joints are neat, and the tile surface is clean. Soak and rinse the sponge repeatedly to avoid dragging, and over saturation. Allow twenty minutes to an hour to dry. Rubber gloves should be worn for this.

Dry dust the surface. When the surface is dry, it should look hazy. Polish the tiles with a fine rag, or an old t-shirt. Be careful not to apply pressure on the joints. If there are any stubborn spots on the tiles, they can easily be scraped off with a plastic scraper. Gloves and a dust mask should be worn for this.

How Removing Tough Stains and Keeping a Sink Clean?

Sprinkle baking soda. If your bathroom sink is still dirty after you’ve done a light clean, you should sprinkle baking all over the sink. Cover as much of the surface as you can. The abrasive force of the baking soda will help remove tough stains. Make sure the sink is dry before you sprinkle the baking soda. Use as much baking soda as you need to cover the surface area of the sink. Take care to sprinkle some baking soda into the grout ring around the drain.

Scrub the sink. Take a clean cloth and scrub the sink down. You may have to apply a lot of pressure in areas that are particularly dirty. Without scrubbing your baking soda into the sink, you won’t be able to remove all stains. Swirl your cloth around in circles while you rub the baking soda into the surface of the sink. Consider using a regular cotton cloth. Microfiber may not have the abrasive power you need to remove some stains. In some instances, you may need to use a mildly abrasive dish sponge.

Rinse the sink. After you’ve scrubbed the sink, you need to thoroughly rinse it to remove all leftover baking soda. If you don’t rinse it immediately, some of the stains may re-set and all your work will be wasted. Make sure to run the water until all the baking soda has washed down the drain. If your sink doesn’t drain properly, you may need to wipe the baking soda out with cloth rags or paper towels.

Rinse the sink after every use. By rinsing the sink after every use, you’ll make sure that dirt and soap residue are washed out of the basin into the drain. This is important, as the dirt in your sink accumulates on a day-to-day basis. Run the water after you brush your teeth, otherwise toothpaste and toothpaste residue will build up in your sink. Make sure you use enough water to wash soap and soap residue down the drain after you wash your hands. If you notice any grime in your sink after you use it, run the water.

Don’t wash hair shavings down the sink. One of the easiest ways to keep a bathroom sink clean is to avoid washing hair shavings down it. Hair shavings not only dirty your sink, but they can partially clog your pipes. As a result, normal dirt and grime will build up in the basin. If you shave in front of the sink, put a towel over the sink so your hair falls into the towel. If you do wash hair down the drain of the sink, your sink will eventually clog up. When this happens, you’ll have to remove the accumulated hair with a coat hanger, or use a chemical clog removing product.