Posts

How Filling Gaps and Sanding the Tub?


Prepare the epoxy putty before applying it to any cracks. Wear rubber gloves to protect your skin, and read the manufacturer’s instructions before you begin. Open up the putty and tear or cut off a small section of the putty. Work the putty between your fingers until it is pliable, kind of like how you would massage a piece of play dough to work it into a new shape. If you can’t find epoxy putty, buy a similar kind of tub-repair paste from your local hardware store.


Fill any cracks or chips in your tub with the epoxy putty. Use your fingers to push putty into any chipped areas. Depending on how large the crack is, tear your putty pieces so the size is about right to just overfill the area. Make sure to push down on the putty firmly so that it makes its way into all the crevices. At this stage, it’s okay if the putty isn’t flat with the rest of the tub’s surface.


Use a putty knife to smooth over each of the patched areas. Take your putty knife and position the blade so it’s flat against the surface of the tub. Gently scrape it over the filled sections to remove any excess putty. Wipe off the blade from time to time with a damp paper towel. If your working on a curved area, you may need to adjust your knife’s position a few times to get the entire area smooth.


Sand the entire bathtub to work down the gloss and prepare it for paint. Use wet/dry sandpaper, and sand it with 400 grit sandpaper first, and then do it again with 600 grit sandpaper. Attach your sandpaper to a sanding block, and use a spray bottle to wet down the tub as you work. The wet-sanding will eliminate a lot of dust, but it’s a good idea to keep wearing your respirator, especially if you’re working in a small space.


Rinse out the tub and dry it completely before painting it. After the tub has been sanded, rinse out the interior and wipe down the exterior sides to remove any sandpaper and grit remnants. Use clean towels to dry it off thoroughly. The tub needs to be 100% dry before you start painting it, so use as many towels as you need to.

The selection of the bathroom cabinet and the details of the bathroom decoration

In the bathroom, it is a small branch in the architecture system, which is often ignored. Our attention to its functionality is often far greater than its decoration and space design. Because whether we go to the toilet or bathing, the first requirement for bathroom is not clean. Not big? Do you sit in a toilet or a squat? The bathroom is not big. Do you have a bathtub? Besides, it seems that there are no other concerns.

Bathroom not only refers to toilets, but toilets, toilets, baths. According to the layout, toilets can be divided into three types: independent, dual-purpose and eclectic. According to the form, it can be divided into semi open, open and closed. The space between the bathroom will not be very large, and the utilization rate of light will be very large in this narrow space. Bathroom lighting brightness is not very high, too high brightness will easily glare through the mirror to form glare. The cool and shades of lamps that can increase the sense of space should be the best choice.

The bathroom lighting design consists of two parts, one bathroom part and one bathroom section. The bathroom space is dominated by soft light. The demand for illumination is not high, and the light is uniform. The light source itself also has waterproof function, heat dissipation function and not easy water accumulation structure. The general light source is designed in smallpox and walls. In fact, in a lot of cases, the light in the bathroom with the top of the bathroom is darker than the ideal illumination. The bathing bully is not suitable for the bathroom lighting because of the strong light and heat. There should be a special lighting source to solve the problem.

Because of the cosmetic function requirements, the bathroom has higher requirements for the color rendering index of light source. Generally, the high-grade light source with good color rendering is required. The control degree and the angle of light are also higher. It’s best to be on both sides of the makeup area, followed by the top. It is also relative to the brightness of incandescent lamps above 60W. At the same time, in this part of the use of light source is more lively, LED lights, chandeliers and so on in this space will be more useful.

The material of the bathtub is acrylic, cast iron, and steel plate. Acrylic material is now the mainstream, acrylic bathtub is 3-5MM acrylic plate vacuum molding, back coated multilayer glass fiber, good insulation effect, smooth surface clean clean decontamination, the price is moderate. Cast iron bathtub is very heavy, durable, long service life and high price. Strong, wearable, high flatness, smooth glaze, lower price relative to cast iron bathtub. No matter what kind of material of the bathtub to drain the drainage is a good match before the factory, this part is easy to be ignored and the most easily out of the problem. When buying, you must try the drain valve on the spot and operate several times to check whether the switch is sensitive and reliable.

Whether the faucet is plated with copper is usually heavier with copper material. The “heart” of the faucet determines the life of the faucet and the effect of water. It is better to use ceramic spool. The water outlet of the general tap is covered with a rectifying net cover, and a good tap outlet has a double-layer filter screen, which makes the water smooth and smooth without splashing and bubbles, and saves water by 30%. The plating layer can not be maintained for a long time without special maintenance. Good plating has 3 layers, good static surface effect, and guarantees that life will not fall off.

Precautions for the maintenance of the flower shower head

When most people are in the shower, they find that the longer the shower head is used, the smaller the water flow is, that is because the maintenance of the shower is not noticed and the shower head is blocked. The shower head is not installed for a long time, but it is blocked by the head. This may be caused by the poor quality of your shower head. But if your shower head has been installed for a long time, use long time, meet the shower head blockage, this is due to the long time water spray head, the impurities in the water will accumulate into the shower head, long time will cause the shower head blockage, belongs to the normal situation.

If it is due to the poor quality of the shower head, it is necessary to pay attention to the quality of shower head when choosing and choose a qualified shower head. In general, it is necessary to buy regular and large-scale commodity inspection, and can not greedy for small cheapest, choose the shower head of plastic and other products, and the shower head of copper should be selected to prevent the quality problems such as plugging and cracking in the shower head.

If it is caused by the long time use of the shower, we need to clean the shower head regularly in our daily life. Generally, we can use white vinegar to remove scale: Every three months to carry out a cleaning work, the shower head is dismantled, soaked in a basin with white vinegar, time is about 4-6 hours, then the spray head clean, installed back, in the water after the scale will be outflow, so that the cleaning of the scale, the elimination of fine bacteria effect.

Manual cleaning needs to remove the net cover of the flower spray, or remove the other scale from the scale and clean it with the brush before installing it back to its original place. Some flower shower head sprinklers will be equipped with some special dismantling tools at the time of purchase, so that they can be conveniently used by consumers. Some of the outflow of its outlet is used in the design of rubber particles, its touch is comfortable, soft, not fouling, but also very convenient to clean, as long as the fingers are used to light the particles will be able to clean the scale. This is the cleaning method chosen by using the characteristics of materials. It is a popular way of cleaning in the market. Many of the shower head are made up of special structures. They can be cleaned automatically when they are used. Flower shower head with cleaning needles, which do not need manual cleaning, can bring out the scale. It is very convenient.

Apart from paying attention to cleaning, we should also pay attention to the daily maintenance of its surface. When we need to use it, keep its surface clean, usually soft cloth, dip the flour to wipe its surface, rinse with clean water to keep its surface clean and prolong its service life. Regular cleaning, white vinegar can be used to soak and rinse the surface and interior of the shower head, and then use cotton cloth as the outlet of the shower head to clean it. This can not only reduce the impact of the scale on the spray, but also play the role of sterilization and disinfection.

For the surface of the shower head, it can be cleaned regularly with flour and rinsed with water, so that the surface of the shower head can be as bright as new. When cleaning the scale, remember not to use strong acid to clean it, otherwise it will easily damage the surface of the shower head. Do not disassemble and maintain the shower head itself, and prevent incorrect methods from damaging the appearance or internal structure of the shower head. The use of the daily use of the environment should not exceed 70 degrees, otherwise it is easy to reduce the life of the shower head, therefore, the installation of the spray should be far away from the electrical source.

bathroom renovation which toilet flushing is more convenient

Bathroom Renovation: Which Toilet Flushing Is More Convenient?

bathroom renovation which toilet flushing is more convenient

 

Toilet flush way has straight style and siphon type, each of these two ways have their own advantages and disadvantages, users can choose their advantages and disadvantages when selecting, which is best suited to their own.

Straight into the toilet flushing is very simple, is to use the water itself gravity and speed the dirt washed clean, the pipeline has the advantages of simple structure, short path pipe thick, not easy to be blocked, even after using the toilet to toilet paper and throw it in is not easy to be blocked. But the straight flush toilet has a relatively loud sound. It is easy to wake up the family if it is installed in the house and gets up at night. The biggest disadvantage of this toilet is very easy to make a stink in the home, because the pipeline is straight, the smell from the pipeline to diffuse throughout the room, but also in summer easily from the pipe out mosquitoes. Straight flush toilets are now newly renovated houses are rarely used, mostly public toilet used more.

The main way of siphon toilet flushing is to use the suction of the pipe in the toilet and a certain water level drop force to discharge the dirt. The water storage area of the toilet is large, and the noise when flushing is very small, because the suction force is large, the flushing is relatively clean, and the toilet surface does not leave some unclean filth. Siphon type toilet pipe is bent, the smell is not easy to play, relatively clean. There are many ways to flush the siphon toilet in the market now. There are vortex siphon toilets, flush methods, and flush toilets. But siphon toilets are more likely to clog up and do not throw waste paper into the toilet. Siphon toilets are prone to flush toilet problems and are more troublesome.