Turn off the water at the main line. The first step is to shut off the water for the bathroom you’ll be working in. Locate the main line and turn it all the way off. Then, turn on the faucet in your tub to drain the lines. Remove the accessories and disconnect the water lines. Use a screwdriver to unscrew the faucet and disconnect it from the water lines by unscrewing it.
Remove the handles, overflow drain cover, and the drain cover on the bottom of the tub. If you have a showerhead, remove that as well. You may need to pry off a plastic cover to gain access to the screws. You may be able to reuse some of these accessories, so keep them if you don’t want to buy new ones.
Remove the existing tub surround or tiles. You need to expose the studs in the wall in order to install a new bathtub, so you must remove the existing surround and the drywall behind it. Using a utility knife, cut through the drywall around the outside edge of the entire surround. Then, use a pry bar to pry the drywall and surround or tiles out of place. Be careful not to damage any pipes or wires.
Be sure to wear safety gear, including goggles and a dust mask, throughout this process. Work from the top of the surround down to the bottom. Gain access to the plumbing. In some homes, you may be able to access the plumbing from the room next to the bathroom. In other cases, the plumbing may be situated in the floor under the tub. Most likely, you’ll need to cut a hole in the wall or floor in order to access the plumbing.
Take out the old tub. First, unscrew the tub drain and overflow from the P-trap underneath the tub. If your tub is acrylic or fiberglass, cut it into pieces with a jigsaw to make the removal process easier. If you want to try to keep the tub in one piece, use a jigsaw to cut away the tub flange that’s nailed to the studs, then tip up the tub and pull it out. You may need to slice through the caulk that connects the tub and floor before removing the tub. Use a utility knife to do so.
https://baranasanitary.com/wp-content/uploads/2019/09/Removing-the-Old-Bathtrub-3.jpg7501150adminhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadmin2019-10-04 08:00:482019-09-24 03:26:27How Removing the Old Bathtrub?
Not a fan of harsh chemicals to clean hard water stains from your tub? Do you need an alternative way to get the tub clean without bringing toxic fumes into your life? In some cases there’s no other way to clean but with chemicals. However, if you clean on a regular basis and stay on top of soap, scum and mold build up you should be able to get the job done with grapefruit and salt.
Slice a grapefruit in half. You should only need half of the grapefruit to get the job done in the tub so either save the other half for lunch or use it on other areas of the home. Locate a box of sea or Kosher salt. You want the larger granule of salt for more exfoliation power. If you don’t have larger grained salt, you can still use regular table salt, but you will need wider coverage when cleaning.
Rub the grapefruit all over the tub, allowing the juice to run all over the tub. Make sure the juice stays in the tub and doesn’t run onto the floor. Sprinkle salt over the tub and the grapefruit juice. The juice should allow the salt to cling to the tub. You only need about ½ cup of salt for the entire tub as you will be rubbing it over porcelain and fixtures.
Rub and scrub the grapefruit into the salt, lifting stains and grime. If necessary, apply a scrub brush or washcloth to the area for extra cleaning power. Allow the grapefruit/salt combo to stand in areas that are especially tough or stained. Wipe salt and grapefruit away as you work.
Rinse with clear, warm water. Turn on the tub faucet and run your hands around the tub to encourage the grapefruit and salt to go down the drain. Use a washcloth to rinse and encourage a squeaky-clean surface.
https://baranasanitary.com/wp-content/uploads/2019/07/clean-bathtub-with-grapefruit-salt-1.jpg7501150adminhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadmin2019-07-31 08:00:022019-08-29 03:52:23How to Clean Your Bathtub with Grapefruit and Salt?
The utility model has the advantages of permeability, moisture resistance, good processing performance and little occupation, and is suitable for the space division of toilets. As a result, shower rooms are usually made of glass or plexiglass. Organic glass because of its anti-aging, strength, wear resistance and other aspects of poor performance, the use of it made shower room is less and less. Ordinary glass due to poor rigidity, fragile, so the security is not good. Therefore, the responsible manufacturers of shower rooms are made of toughened glass with strong strength, rigidity and other aspects.
Consumers choose shower room, from the angle of safety and durability to consider, we must choose tempered glass products. But the appearance of toughened glass and ordinary glass, it is difficult to distinguish with the naked eye, so be sure to choose a large scale, high degree of credibility, customer service service guarantees brands and businesses in the purchase of the shower room, to ensure buy high-quality products.
By the way of door switch, shower room is divided into slide type and hinge type. In the early days, the shower room was all slide type, and the slide and the top edge of the shower room were provided with sliding rails. The door was embedded in the slide rail and turned back and forth for the switch. The slide is easy to scale or fall into hard objects cannot be cleaned, the door switch is not smooth and cause damage. Moreover, the slide rail itself has the disadvantages of shorter service life and greater noise when pushing and pulling. Therefore, the shower room with higher grade has been upgraded to hinge type now. The hinge type shower room usually adopts the frameless design, and the appearance is concise and fluent. It is widely welcomed.
Hinge type shower room, glass door weight completely by the hinge to bear, because the glass door is very heavy, the hinge quality requirements are very high, the requirements of corrosion resistance, fatigue resistance, bearing capacity. There are two kinds of hinge of different materials on the market: copper plating and stainless steel casting hinge hinge, stainless steel hinge for die casting are slightly better than in appearance, strength, corrosion resistance and other aspects, so relatively well-known brands tend to choose die casting stainless steel hinge, shower room to ensure safe use, prolong the service life.
Some of the European import brand hinge, shower room, the glass door is 180 degrees out of arbitrary switching function, the use of more convenient, it may not be in the shower when the glass door is pushed to the shower room inside, convenient cleaning.
Arc, right angle, or a shape, according to the pattern of the bathroom
Shower room has three main styles: arc, right angle and shape. The first two shower rooms should be installed in the vertical corner, in the bathroom corner of the bath area, more suitable for a larger area, roughly Square Bathroom use. A shaped shower room by in a straight line, with metal hinge connecting the glass door and the glass screen. The two ends are respectively fixed on opposite walls, will be separated into one end of the toilet, bathing area, generally suitable for rectangular or irregular shape of the toilet toilet.
Don’t neglect the function of the sealing strip
he main function of shower room is to wash away the splash of splash, so choose to pay attention to whether the selected products are sealed in the connection of glass and glass, glass and wall. If not, it is difficult to spray nozzle splash block bath, shower room effect is therefore greatly reduced. And high quality shower room sealing strip should not have a breakpoint at the hinge, glass door seal between the magnetic, so that water retaining performance will be better.
The shower room is mainly composed of tempered glass, toughened glass and the edge is relatively weak, when the attention do not use hard knock glass corners, so as to avoid damage. A better choice of glass edge sealing strips are the product, because the seal may be appropriate to alleviate the impact force generated bump, a safety protective effect on toughened glass.
Manufacturers provide free installation better
As the glass shower room is relatively heavy, so the installation of better wall is load-bearing wall, or not less than 15 cm thickness of the solid wall, so that security is guaranteed. But for the use of thin tempered glass shower room, 10 cm thickness of the solid wall can be installed.
High quality shower room requires higher installation accuracy, otherwise it will affect the appearance and use effect. In addition, the shower room is in use if there are problems, such as not factory installed, it is difficult to determine responsibility, easy to cause the wrangling, causing trouble for consumers. Therefore, it is more reliable to provide professional installation by manufacturers, but it may require consumers to pay additional installation fees. At present, some brands in the market offer free installation services.
https://baranasanitary.com/wp-content/uploads/2017/06/we-teach-you-how-to-choose-safe-purchase-shower-room-1.jpg600900administratorhttps://baranasanitary.com/wp-content/uploads/2017/01/logo-3.pngadministrator2017-06-05 12:24:172017-11-16 11:09:21We Teach You How To Choose Safe Purchase Shower Room
