Posts

The Knowledge of Install a Bathroom Fan


Wait 24 hours before turning on the water. To give the caulk and other adhesives time to dry, wait at least a full day. Then, you can turn on the water and check for leaks. If you find any problems, contact a certified plumber. Make sure you apply this paste to the corners of your shower door’s frame, as this is where rust and soap scum are likely to build up and harder to clean otherwise.


You can run the vent through the sidewall or roof, whichever is most convenient. Just make sure the duct pipe is as straight as possible and that it won’t be stretched too tightly. Attach the vent cap. The process for attaching the vent cap will vary depending on whether the exit point is on the roof or sidewall.


If your exit point is on the sidewall, pick a point between two wall studs and take some reference measurements on the inside so you can locate the same point on the outside. Use a 4-inch hole saw to cut through wall from the outside, then secure the vent cap in place.


If your exit point is on the roof, draw an appropriate sized circle on the inside and use a reciprocating saw to cut it out. Then get on the roof (taking all of the proper safety precautions) and remove the shingles covering the newly cut hole. Install the vent cap, using roofing cement and roofing nails, then replace any loose shingles. Move back into the attic and attach the end of the duct pipe to the vent cap’s connector duct using foil duct tape.


Wire the connections in the housing unit. Depending on the type of fan, you may need to wire the connections from the attic or from the bathroom. Make sure to read the manufacturer’s instructions and double check that the power is off before proceeding. Open up the housing unit and pull out the fan wires from the electrical splice unit. Strip 5⁄8 inch (1.6 cm) back from each of the wires on both the fan cable and the electrical cable you inserted earlier.

How Cleaning Faucets?

Rub in the cleaning agent. Use a sponge, cloth, or soft bristle brush and make tight, circular strokes. If your shower is very dirty, then you may need to rinse your sponge, cloth, or bristle brush in-between passes. Don’t use hard bristle brushes, and never use metal scrubbers. These can scratch your walls and tub.

Rinse the shower wall with clean water. Use your cup or bucket to splash water on the wall, removing the remaining cleaning agent and the grime. If you have a detachable shower head, then use that to rinse the shower wall instead. If your shower wall still looks dirty, then re-apply the cleaning agent and repeat the process. Repeat for the remaining shower wall sections and tub. Spray the next section, let it soak, rub in the cleaner, and rinse for each of the three to four sections.

Scrub grout with a bleach-water mixture. If you have grout, clean it with bleach and a small scrub brush. Mix two parts water and one part bleach. Use a grout scrubber to clean the grout with your mixture. Use an old toothbrush as a scrubber. Don’t clean your grout with bleach and water while you clean your shower walls with the cleaning agent. Mixing chemicals is dangerous. Turn on the shower for a final rinse. Allow your shower to run for about a minute so that the bleach and any remaining cleaning product are rinsed away.

Rinse your faucet. Splash water up over your faucet to wet the surface and wash away debris.You should clean your faucet weekly to remove spots and stains. Toothpaste and soap often leave flecks on faucets, and they are easiest to remove when they are recent. Mix equal parts vinegar and hot water. Create a cleaning and polishing agent using white vinegar and hot water. Your water should be hot, but not boiling.

Wet a cloth. Dip your cloth in your vinegar-water mixture. Be careful not to burn yourself with the hot water. Wipe your faucet to remove spots. Work the cloth in circular movements as you polish away hard water spots and other splash marks on your faucet. Use a clean cloth to dry the faucet so that you don’t leave streaks.