Posts

How Installing the New Tub?


Slide the new tub in place so the flanges rest on the ledger boards. Have a partner help you slide your new tub into place. Feed the drain shoe into the hole in the floor, and set the rest of the tub down. Make sure the tub is level one more time before securing it to the wall. Make sure the tub is in full contact with the floor so the ledger boards aren’t supporting the full weight.


Screw or nail the tub into the studs. Use screws or nails that are 2–3 in (5.1–7.6 cm) long to secure the tub flange to the the studs. Work slowly so you don’t accidentally crack your tub. Put 1 nail or screw into each stud to keep it in place. Tip: If there are any gaps between the studs and the tub flange that are 1⁄8 in (0.32 cm) or larger, put wooden shims in before you put in nails or screws.


Use hardwood shims since soft wood can deform over time. Connect the drain shoe to the pipes. Access your pipes from the hole you cut in the room adjacent to your bathtub. Use a pipe wrench to tighten the drain shoe to the P-trap until it’s completely secure. Squeeze a ring of silicone sealant around the pipe and P-trap for another layer of protection from leaks.


Reattach the faucet. If the faucet had a screw, put the faucet back on with a screwdriver and turn it clockwise. If the faucet screwed off by itself, twist it back on by hand and use a pipe wrench to secure the faucet in place completely.


Fill the tub and test for leaks the day after it’s installed. Let the sealant on your tub dry for 1 day so it’s completely set. Turn the water valve back on and let it fill the tub. Listen for any dripping noises and watch for any noticeable leaks near your drain or on your pipes. If you find any leaks, use more sealant around the leaking area.

How Using the Cleaning Solution to Remove Bathroom Mold?

Spray the mold cleaning solution over the area you wish to clean. Get the spray bottle with your chosen cleaning solution inside. Generously spray the entire area with the solution so that there is a visible, even coating. Try not to completely saturate the area, as otherwise, there will be excessive liquid to clean up later. Aim to apply enough of the cleaning solution so that the area is visibly wet, but not so much that puddles form. Be very careful not to slip if you are working on floor tiles or grouting.

Wipe smooth surfaces with a cleaning cloth to remove the mold. Fold a cleaning cloth into quarters and wipe the entire area where you sprayed the cleaning solution. The mold should wipe away easily onto the cloth. Use a new side of the cloth whenever the first side gets saturated or too dirty. You may need to swap cleaning cloths throughout the process, especially if you are cleaning a large area. Alternatively, you can use a sponge instead of a cloth if you prefer. Smooth surfaces include showers, baths, basins, and tiles.

Use a scrubbing brush to remove stubborn mold from smooth surfaces. If the mold remains, it’s time to take more serious measures! Scrub the affected area vigorously until the mold comes away. Try to clean any mold away as soon as it grows so that you don’t need to resort to scrubbing. Have a dedicated scrubbing brush strictly for bathroom mold to prevent spreading the spores throughout your home.

Scrub grout or caulking with a toothbrush. Use a back and forward motion to remove mold from grout or caulking with an old toothbrush. Rinse the toothbrush under running water to remove any mold while you clean, as this prevents the mold spores from spreading throughout the bathroom. Use a dedicated toothbrush for cleaning mold in the bathroom so that the spores don’t spread throughout your home. You can use a larger scrubbing brush if you prefer, but a toothbrush is the easiest to use in tight spaces. You can purchase specialty grout scrubbers from home improvement stores.

Dry the cleaned area with a cleaning cloth. Remove the excess liquid from the area that you cleaned to keep the bathroom dry and to prevent slips. Run the cloth over all of the smooth surfaces and the grout or caulking to remove the excess moisture. This also removes any mold that has been scrubbed loose. You may need to swap cleaning cloths if the first one gets too saturated. Pay attention to any small crevices or corners to prevent the liquid from pooling up and more mold from forming.