Posts

How Removing Your Existing Tub?

/in /by


Cut a panel behind your tub to access the drain pipes. Most times, the water supply valve for your tub is located in the walls behind the faucet. Go into the room adjacent to your bathroom to cut a hole in the wall where the drain and faucets are for your tub. Use a stud finder so you don’t accidentally cut into one of the studs. Cut an 8 in × 8 in (20 cm × 20 cm) square in the drywall with a reciprocating saw to expose the pipes.


If you can’t access the room adjacent to the drain, cut a hole in the floor beneath the bathroom using a reciprocating saw. Make sure you’re underneath where the tub drains. Wear safety glasses while working with your saw. Turn off the water supply to your bathroom. The water supply for your tub is either controlled by a valve in the wall behind your faucet or by the main water pump. Turn the valve so it’s perpendicular to the pipes to turn it off.


If your valve shut-off is circular, look for the directions printed on the valve head to figure out which way to turn it. If you cannot turn off the water for your tub or bathroom, you may need to turn it off for the entire home or building.


Remove the tub spout. Locate the screw on the underside of the faucet or where it connects to the wall. Use a flathead or Phillips screwdriver to remove the screw. If it doesn’t have a screw, tighten the jaws of a pipe wrench around the back of the faucet and twist it counterclockwise until it’s loose. Then, pull it out. If you want to save the faucet, put a rag in between it and the wrench so you don’t leave any scratches.


Take out the main and overflow drains. A drain removal tool is a cylinder that fits into the drain to loosen its connection to the pipes. Put the end of a drain remover tool in the drain hole and turn it counterclockwise. Keep turning the tool until the drain is loose and you can pull it out by hand. Unscrew the overflow drain, located on the front wall of your tub, and pull it off of the surface.

How Painting the Ceiling and Trim?

/in /by

Start with the ceiling, if you’re painting it. If you’re painting the ceiling, use a brush to cut in around the edges where it meets the walls. Finish the job by using a roller on the end of an extension pole. For best results, use a quality, plush roller cover, which will allow you to get as much paint onto the ceiling in the shortest amount of time.

Dip the roller into the paint tray’s well, then roll up the tray to remove excess. Start in a corner, and roll in a continuous stroke. Try to keep the roller wet, and overlap the painted edges and your previous strokes by about 3 in (7.6 cm). If you’re using a latex paint, you should be able to apply a second coat after 4 hours. For even coverage, apply the first coat in one direction, or north to south, and the second in the other direction, or east to west.

Cutting in is basically coloring within the lines; it’s when you hug a tight edge with the brush. Tip: Choose mildew-resistant ceiling paint, which is flat (not glossy), dries slowly, and spatters less. While mildew-resistant products are a bit pricier, but they hold up better to moisture and last longer.

Paint the trim with a brush before painting the walls. Use an angled brush to paint baseboards and other trim. Paint them first so you don’t have to tape off the walls, which is more difficult than taping off trim. Depending on the type of paint you’re using, apply a second coat after 4 to 24 hours.

Semi-gloss is a good finish for bathroom trim. Baseboards, chair rails, and window and door trim collect dust and grime, and semi-gloss is more durable and easier to clean than flat finishes. White is conventional for trim, but you could experiment with color, especially if your walls are white. Grays, blues, and black are trendy choices if you want your trim to make a statement.

Tape off the trim if you’re not confident about cutting in along edges. If you have a steady, practiced hand, you don’t need to tape around every edge. However, if you want to stay on the safe side, allow the trim to dry for 24 hours, then lay down painter’s tape at the edges where it meets walls. Additionally, tape around your bath fixtures and wall tile.

Even if you have a steady hand, you should still tape horizontal trim, such as baseboards, chair rails, and horizontal runs of tile. Paint will inevitably spatter on horizontal trim, but vertical trim, such as window and door trim, is less vulnerable.